1, The specification of the product including basic size
information, electrical and mechanical properties.
|Basic size information|
|Wire Insulation Diameter||1.00mm Max.|
|Mounting side||Standard on-Board|
|Terminals material||phosphor bronze, tin-plated/gold-flash finish|
|Current Rating||1A AC, DC|
|Voltage Rating||150V AC, DC|
|Contact Resistance||30mΩ Max|
|Insulation Resistance||500mΩ min|
|Withstanding Voltage||500V AC/minute|
|Operating Temperatureemperature range||-25℃ to 85 ℃|
|Other information please kindly check the following picture.|
2, Related drawing and report
3. Ratings & Applicable Wires
|Rated Voltage (Max.)||100V AC/DC||Insulation O.D. 1.50mm (Max.)|
|Rated Current (Max.) And Applicable Wires||AWG#24||2.0A AC/DC|
|Ambient Temperature Range||-25℃ ~ +85℃*|
*: Including terminal temperature rise
4. Electrical Performance
|Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based
upon JIS C5402 5.4)||10mΩ (Max.)|
|4-2||Insulation Resistance||Mate connectors, apply 500V DC between adjacent terminal or ground.
(Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B)||1000MΩ (Min.)|
|4-3||Dielectric Withstanding Voltage||Mate connectors, apply 800V AC (rms) for 1 minute between adjacent
terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method
|4-4||Contact Resistance on Crimped Portion||Crimp the applicable wire on to the terminal, measure by dry
circuit, 20mV (Max.)., 10mA.||5mΩ (Max.)|
5. Mechanical Performance
|5-1||Actuator Insertion & Withdrawal Force||Insert and withdraw connectors at the speed rate of 25±3mm /
minute.||Refer to paragraph 7-2|
|5-2||Crimping Pull Out Force||Fix the crimped terminal, apply axial pull out force on the wire at
the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8)||AWG#24||3.0kgf (Min)|
|5-3||Terminal Insertion Force.||Insert the crimped terminal into the housing.||1.00kgf (Max.)|
|5-4||Terminal/Housing Retention Force.||Apply axial pull out force at the speed rate of 25±3mm / minute on
the terminal assembled in the housing.||1.50kgf (Min.)|
|5-5||Pin Retention Force||Apply axial push force at the speed rate of 25±3mm / minute||1.00kgf (Min.)|
|5-6||Durability||When mated up to 50 cycles repeatedly by the rate of 10 cycle per
minute.||Contact Resistance 20mΩ (Max.)|
Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each
(Based upon MIL-STD-202 Method 201A)
Appearance No Damage.
Contact Resistance 20mΩ (Max.)
Discontinuity 1 μsec.(Max.)
|5-8||Physical Shock||490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS
C0041/MIL-STD-202 Method 213B Cond. A)|
Q:Do you allow multiple design per setup?
A:Yes.We accept OEM service and allow multiple design per setup.
Q:How long does shipping take?
A:It depends on the destination location and quantity. In most
developed world, delivery by Fed x/UPS/DHL is normally 3-5
Q: How is the goods packaged ?
A: Usually in bags, tube, pipe, plated & carton
4, Various payment & delivery way
In order to make you get product quickly and send money easily, we
can offer differenct payment terms
- If the total value of order is less than USD200, please kindly
choose western union or paypal.
- If the total value of order is between USD200 and USD500, please
kindly choose western union.
- If the total value of order is over USD500, please kindly choose
western union or TT.
- If the total value of order is over USD5000, L/C at sight will be
considered by us, but the commision fee will be shared by us